ONKYO PR-SC5508 Bedienungsanleitung PDF herunterladen (Seite 48)

Main menu Speaker Setup

Here you can check the settings made by

Audyssey MultEQ XT32 Room Correction and Speaker

Setup, or set them manually, which is useful if you change

one of the connected speakers after using

Audyssey MultEQ XT32 Room Correction and Speaker

Setup.

Note

• These settings are disabled when:

– a pair of headphones is connected, or

–the “Audio TV Out” setting is set to “On” (➔ 60) and an

input selector other than HDMI is selected.

Speaker Settings

If you bi-amp the front speakers, you must change the

“Speakers Type(Front)” setting (➔ 48). For details on

speaker wire connection, see “Bi-amping the Front Speak-

ers” (➔ 16).

Note

• When bi-amping is used, the AV controller is able to drive up to

7.2 speakers in the main room.

• Before you change these settings, turn down the volume.

■ Speakers Type(Front)

` Normal

Select this if you’ve connected your front speakers

normally.

` Bi-Amp:

Select this if you’ve connected your front speakers

for bi-amped operation. The Bi AMP indicator will

light (➔ 9).

Note

• Surround back speakers cannot be used if you select “Bi-Amp”.

•If the “Front High + Front Wide” setting is set to “Yes”, the

“Speakers Type(Front)” setting is fixed at “Normal”.

■ Front High + Front Wide

` Ye s:

Front High + Front Wide on.

` No

Front High + Front Wide off.

Listening mode that make use of “Front High + Front

Wide” setting is as follows;

Audyssey DSX (PLII/Neo:6 + Audyssey DSX included),

Orchestra, Unplugged, Studio-Mix, TV Logic, Game-

RPG, Game-Action, Game-Rock, Game-Sports, All Ch

Stereo, Full Mono.

Note

• When you have selected “Ye s”,

–the “Surround Back” setting is set to “None”.

–the “Front High” or “Front Wide” setting is set to

“80Hz(THX)” if set to “None”.

• When you have selected “No”, the “Front Wide” setting is set

to “None” if “Front High” and “Front Wide” settings are set to

anything other than “None”.

•The “Front High + Front Wide” setting cannot be used if

“Speakers Type(Front)” is set to “Bi-Amp”.

Speaker Configuration

With these settings, you can specify which speakers are

connected and a crossover frequency for each speaker.

Specify “Full Band” for speakers that can output low fre-

quency bass sounds adequately, for example, speakers

with a good sized woofer. For smaller speakers, specify a

crossover frequency. Sounds below the crossover fre-

quency will be output by the subwoofer instead of the

speaker. Refer to your speaker’s manuals to determine the

optimum crossover frequencies.

If you set up your speakers using Audyssey MultEQ XT32

Room Correction and Speaker Setup, please make sure

manually that any THX speakers are set to “80Hz(THX)”

crossover.

■ Subwoofer

` 1ch:

Audio signal is outputted from SW1 jack only.

` 2ch

Audio signal is outputted from SW1 and SW2

jacks.

` No:

Select if no subwoofer is connected.

■ Front

` Full Band

` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)

90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is

fixed at “Full Band”.

■ Center

, Surround

, Surround Back

*2*3*4*5

` Full Band

` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)

90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

` None:

Select if no speaker is connected.

■ Front Wide

*1*2*6

, Front High

*1*2*6

` Full Band

` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),

90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

` None

Select if no speaker is connected.

Speaker Setup

Some of the settings in this section are set automatically

by Audyssey MultEQ

XT32 Room Correction and

Speaker Setup (➔ 29).

If you change these settings, you must run

Audyssey MultEQ XT32 Room Correction and

Speaker Setup again (➔ 29).

This setting is set automatically by

Audyssey MultEQ XT32 Room Correction and Speaker

Setup function (➔ 29).

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 107 108

Kommentare zu diesen Handbüchern

Keine Kommentare

ONKYO PR-SC5508 Bedienungsanleitung Seite 48

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für AV-Receiver ONKYO PR-SC5508