ONKYO TX-NR737 Bedienerhandbuch PDF herunterladen (Seite 8)

Step 2:

Setting Up

After placing the microphone at the measurement

position, select "Do it Now" with the cursors and

press ENTER.

Connect the microphone to the SETUP MIC jack of

the unit.

SETUP MIC jack

Speaker setup

microphone

Follow the guidance displayed on the TV screen.

AccuEQ Room Calibration

Front Speakers Type

Powered Zone 2

Back/Height

Subwoofer

Normal

Back

Yes

Set bi-amp only if you use 2 channel amp for each front speaker.

ENTERNext

When the screen above is displayed, set the items with

the cursors on the remote controller. When the cursor

is on an item, the content of the item will be shown on

the lower left of the screen. After setting the items, press

ENTER on the remote controller. Press ENTER also in

the next screen,

The test tones sound from the connected speakers

and automatic speaker setting starts.

Measurement will be made twice for each speaker. It

takes several minutes to be completed. Keep the room

as quiet as possible during measurement. If any of

the speakers do not produce the test tone, check for

disconnection.

When the measurement is completed, the

measurement result is displayed.

Press

on the remote controller to check the

settings. Press ENTER with "Save" selected. In the next

screen showing that "AccuEQ" is "On", press ENTER on

the remote controller.

• If there is an error message, follow the on-screen

instruction to remove the error cause.

• Sometimes due to the electrical complexities of

subwoofers and the interaction with the room, THX

recommends setting the level and the distance of the

subwoofer manually .

• Sometimes due to interaction with the room, you may

notice irregular results when setting the level and/or

distance of the main speakers. If this happens, THX

recommends setting them manually.

• Please note that any THX main speakers should be

set to Small (80Hz). If you set up your speakers using

Auto Set-up, please make sure manually that any

THX speakers are set to Small with 80Hz crossover.

When "Please unplug setup microphone." is

displayed, disconnect the microphone.



2nd Step : Source Connection

You can check whether or not each input source is

connected correctly.

When the Source Connection start screen is

displayed, select "Yes, Continue" with the cursors

and press ENTER.

This step will start to check if the

connections were made correctly.

Would you like to continue?

Yes. Continue

No. Skip

Initial Setup

Source Connection

ExitHOME

Select the desired input to check the connection and

press ENTER.

Start playback of the selected device. If connection is

correct, video/audio of the input source selected on the

unit will be played.

After checking the connection, select "Yes" with the

cursors and press ENTER.

• If you select "No" and press ENTER, the error cause

will be displayed. Follow the guidance to remove the

error cause and check the connection again.

Select "Yes" with the cursors and press ENTER

on the remote controller to check the connection

of other inputs or select "No, Done Checking" and

press ENTER to skip.

If you select "Yes", you will return to the screen of step 2.

If you select "No, Done Checking", you will proceed to step 5.

Enabling HDMI Linked Operation and Other

Functions

In the next screen, you can enable the HDMI linked

operation with CEC compliant device, connection with

ARC compatible TV, and HDMI Through function. Select

"Yes" with the cursors to enable them or "No, Done

Checking" to skip, and press ENTER on the remote

controller.

Select "Yes" with the cursors and press ENTER to

enable the CEC link function or select "No" and

press ENTER to keep it disabled.

The following CEC-compatible devices are found;

Do you wish to turn on the CEC link?

Integra DHS-8.8

Yes

Source Connection

ExitHOME

If you select "Yes", the connection with ARC compatible

TV and HDMI Through function will be set to "Auto" and

enabled.



3rd Step : Remote Mode Setup

In this step, you can enable operation of the other

components using the remote controller of the unit. When

the Remote Mode Setup start screen is displayed, select

"Yes" with the cursors and press ENTER on the remote

controller. Follow the guidance to select the desired

REMOTE MODE button and in the keyboard screen, enter

the first three characters of the brand name of the device

you are going to program (e.g., "ONK" for ONKYO) and

search for the remote control code. The guidance will also

explain how to set the remote controller.

HOME Exit

Initial Setup

Remote Mode Setup

Preprograming remote will give you control

of other devices from AV receiver remote

Would you like to setup your remote to

control your devices? This may take a while

depending on what and how many you have

connected. You can always come back to remote

setup from setup “8-2 Remote Mode Setup”.

Yes

No. Skip

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

ONKYO TX-NR737 Bedienerhandbuch Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für AV-Receiver ONKYO TX-NR737